![]() Smartctl 7. Here is the output of the smartctl command : I tried with and without secure boot, just in case, same thing. I also tested from my Debian unstable, but also from a live usb with Fedora 32. I don’t think it’s an issue with the disks. I happen to have the same issue with both ssd, which are not the same (250GB and 500GB versions). (See this posting for determining the correct device/namespace and LBA Format index number.) $ sudo nvme format /dev/nvme0n1 -lbaf= 1 -reset One more thing, before you try to low-level format it, unmount the filesystem on the NMVe drive first. The controller may perform a cryptographic erase when a User Data Erase is requested if all user data is encrypted.ĭo you have an encrypted disk? If not then try removing the -s 1 option. Defaults to 0.ġ = User Data Erase: All user data shall be erased, contents of the user data after the erase is indeterminate (e.g., the user data may be zero filled, one filled, etc). The erase applies to all user data, regardless of location (e.g., within an exposed LBA, within a cache, within deallocated LBAs, etc). ![]() Secure Erase Settings: This field specifies whether a secure erase should be performed as part of the format and the type of the secure erase operation. This guide describes this rather complex procedure in English, in a very good way IMHO.Toniob: nvme format -lbaf=1 -s 1 -f /dev/nvme0n1 You will lose all your data on it, but if you managed to back it up, then it's not a big deal. If you get a successful recognition, quickly backup all your data, as it might be your last chance to do so.Īt that point you may want to try to revive your drive, you need to use SandForce's official software do so. You may try multiple times before giving up, as it is your only chance to recover your SSD without losing data. This operations might work if the controller got stuck after an improper SATA wake-up command after hybernation. Then shutdown your computer and wait another 5 minutes. ![]() Try to unplug it from its socket, wait 5 minutes, then plug it back in and open the BIOS, leaving it open for 10 minutes. Flashing the controller will inevitably lead to the loss of all your documents.īefore starting a flashing procedure you can always try having the SSD to " cycle", in order to force it out of panic mode. Unfortunately, you will not be able to retain your data. You can fix this within Linux: you'll need to operate with Fedora, in order to force-flash a new firmare on the SSD's controller. It is a common issue with SF-2000 controllers. The contents on the drive are quite important, so if possible, I'm trying to recover this drive in a non-destructive way.Īs your drive is recognised as SandForce, this means that your SSD controller is stuck in "panic mode". If this is the issue, is there any way to fix this from within Linux? What further steps should I do to try to recover this drive? I/O size (minimum/optimal): 4096 bytes / 4096 bytesįrom what I can tell, the issue may be caused by the "DevSlp" feature of the SSD ( ). Sector size (logical/physical): 512 bytes / 4096 bytes Physical block size: 512.00 Byte (2^9 Bytes)įdisk: Disk /dev/sdb: 32 KiB, 32768 bytes, 64 sectors Doneīad news: The device `/dev/sdb' is damagedĪpproximate cache size: 0.00 Byte (0 blocks), need-reset=no WARNING: Probing normally takes from a few seconds to 15 minutes, but This is free software see the source for copying conditions. To continue, add one or more '-T permissive' options.Ĭopyright (C) 2010 Digirati Internet LTDA. SMART support is: Unavailable - device lacks SMART capability.Ī mandatory SMART command failed: exiting. Sector Sizes: 512 bytes logical, 4096 bytes physicalĭevice is: Not in smartctl database ĪTA Version is: ATA8-ACS T13/1699-D revision 4 Smartctl 7.1 r5022 (local build)Ĭopyright (C) 2002-19, Bruce Allen, Christian Franke, = START OF INFORMATION SECTION = I also tried using PNY's firmware update tool, but it didn't detect my SSD (even when installed internally).īelow is the output of smartctl: # smartctl -a /dev/sdb However, I am not using an Intel SSD, so the firmware update doesn't apply. After some Googling, I found this Intel thread which seems to describe my problem: The kernel detects the new device, but it refuses to mount it or perform any operations on the block device, stating, "I/O Error". With the Data Migration, you can easily migrate your current operating system, application software, and user data to your new Samsung SSD. Plugging it into my new laptop via SATA-USB adapter, I noticed a few interesting things. Data Migration is designed to help you migrate all of your data quickly, easily, and safely from your existing storage device (e.g. The drive shows up in the BIOS as a "0.0GB Solid State Drive", when it used to show PNY and the serial number. Then suddenly the laptop stopped booting. I have a PNY "CS1111" 240 GB SSD which I was using in my old laptop.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |